Go To...

Electrical Question

Home › Forums › Tech Help › Tech Help › Electrical Question

This topic contains 9 replies, has 0 voices, and was last updated by  Jeffrey Smith 11 years ago.

Log In Register Lost Password
Viewing 10 posts - 1 through 10 (of 10 total)
  • Author
    Posts
  • October 28, 2014 at 2:34 am #104228

    Jeffrey Smith
    Member

    So the aftermarket headlight cowl on the 690 was coming away due to poor mounting technique (keep it clean guys) so I pulled it off to strengthen the setup and in doing so I came across this electrical connector that has burnt out. It is for the heated grips and I assume is on the low temperature side of the switch as only the high setting was working.

    So the question is, what is it and where can I get a replacement?

    IMG_2945_zps77f3ac2e.jpg

    IMG_2952_zps55d92265.jpg

    October 28, 2014 at 2:44 am #260060

    Greg
    Member

    Its a resistor, not sure if you can buy them separate. Try Scott at Sutto’s or Brad at Ballards

    And yes its needed, I will look I may have a spare kit that has been robbed

    TB

    October 28, 2014 at 2:56 am #260064

    Jeffrey Smith
    Member

    Thanks mate. I will try Jaycar as I head back OS on Thursday morning. If they don’t have them I will try the others when I get back

    October 28, 2014 at 3:54 am #260061

    Adam Rodgers
    Member

    Jeffro,

    Jaycar certainly sell them.

    You need the resistance and wattage, hopefully still visible on the old one.

    Adam.

    October 28, 2014 at 5:19 am #260065

    Jeffrey Smith
    Member

    Your right Adam, Jaycar do sell them (all sizes) but knowing what resistance and wattage is the big thing and unfortunately the markings on the old one are long gone. I will need to do some research to find out what is required including working out what brand the grip warmers are. Lucky winter is a fair way off.

    October 28, 2014 at 6:02 am #260062

    Dwayne O
    Member

    I had the same sized resistor on the heated grips I used to run.
    I put a strip of heat shrink over the top of the resistor and it gave it some protection from doing what yours has done Jeffro. I did have one fall apart early days and sourced a new one from Jaycar.

    I may have a spare resistor here somewhere too mate, I will dig around in the cave and let you know if I find it. You can have it if it`s still there mate (next time your home for a visit) ;)

    October 28, 2014 at 6:16 am #260066

    Jeffrey Smith
    Member

    Thanks Eags

    October 28, 2014 at 8:33 am #260067

    Steve
    Member

    wtf are heated grips .haven’t needed a hot water bottle (to go to bed ) for years.
    harded the bugger up.get some bark busters,will take away the wind chill of your little fingies.

    toes :)

    October 28, 2014 at 8:33 am #260063

    Dwayne O
    Member

    Sorry mate :whistle
    I have failed to find it this evening,,, I will continue to look and if it turns up it is yours.

    I did however do some prep on the 690 for the upcoming Nav ride :)

    October 28, 2014 at 8:57 am #260069

    Jeffrey Smith
    Member
    toes wrote:
    wtf are heated grips .haven’t needed a hot water bottle (to go to bed ) for years.
    harded the bugger up.get some bark busters,will take away the wind chill of your little fingies.

    toes :)

    Thanks for the tips toes, I will take them on board mate. ;)

    p.s. I didn’t fit them, they were on the bike when I bought it

  • Author
    Posts
Log In Register Lost Password
Viewing 10 posts - 1 through 10 (of 10 total)

You must be logged in to reply to this topic.