Go To...

FOR SALE 300 EXC

Home › Forums › For Sale › For Sale › FOR SALE 300 EXC

This topic contains 1 reply, has 0 voices, and was last updated by  Shane Cosgrove 11 years, 6 months ago.

Log In Register Lost Password
Viewing 2 posts - 1 through 2 (of 2 total)
  • Author
    Posts
  • September 28, 2013 at 4:56 am #103289

    Shane Cosgrove
    Member

    Christmas looks like its coming early and the new 300 is on its way. Time for the 07 to find a new home.

    Had a top end rebuild last year, one fork seal weaps a little but a have new one here in the shed ready to go on.

    Brand new FMF Gnarly pipe,
    Misc Blingy bits
    Radiator guards,
    bark busters,
    FMF powerparts muffler
    New 13T front sprocket
    New wheel bearings and seals front and back
    Electric Starter and bendix gear recently serviced
    New starter etc last year, Old one is fine and comes with bike
    Hyde pipe guard (not fitted but if you want it thats fine)
    bashplate (same as above)
    Old FMF pipe is available, its fine just a not as pretty as the new one.
    Aftermarket pegs, wider than standard
    Comes with all manual, powervalve springs, spare jets and needles for tuning to your preference.

    Like all my babies if it needs anything its gets it. Goes great and serviced after every ride, not just oil and filter but lanolin on every adjuster, bolts tighted, throttle cable lubed etc. I usually oil change every three rides, was last done at frying pan last weekend between rides :)

    These are going for about 6K mine has 5600 KLM on it, (more after tomorrows ride :) so make an offer

    Pics below, Will replace the silly stickers on the front guard with anything you like if it takes your fancy :)
    (Mrs Squiggle has a vinyl cutter :)

    [img]http://www.vinesit.com.au/photobucket/KTM300/1.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/2.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/3.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/4.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/5.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/6.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/7.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/8.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/9.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/10.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/11.JPG[/img]

    [img]http://www.vinesit.com.au/photobucket/KTM300/12.JPG[/img]

    October 14, 2013 at 10:48 am #250218

    Shane Cosgrove
    Member

    bump!

    New chain fitted on the weekend and I serviced and replaced the seal on the left fork 2 weekends ago, IE 2 rides ago. Also new rear bearing installed and new rear tire.

    New bike should be good for next week so this bike and the 250 will both go on gumtree etc as well. PM if your interested.

  • Author
    Posts
Log In Register Lost Password
Viewing 2 posts - 1 through 2 (of 2 total)

You must be logged in to reply to this topic.