nipples

Home Forums Yamaha Bikes Yamaha Bikes nipples

This topic contains 23 replies, has 0 voices, and was last updated by  DAVE PURDOM 16 years, 2 months ago.

Viewing 15 posts - 1 through 15 (of 24 total)
  • Author
    Posts
  • #95559

    DAVE PURDOM
    Member

    Ok just had a read over on KB(kiwi biker) in the off road section, and someone said if you drill and tap into the steering head behind the front number board, and about half way between the top and bottom bearings and fit a grease nipple and fill the steering head full of grease no more steering head bearing problems, … anyone on here tried it ???

    #115575

    Mick D
    Member

    Yeah I am sure TB did it once.I believe there is a story behind it to,something to do with the fuel tank breather hose from memory.
    TB will fill you in on it.

    #115576

    Greg
    Member

    Yeah my 1st XR600 was done, only thing is if the bike is a trail bike and has a steering lock fitted you need the fill the slot in the inner tube (triple tree tube, bottom clamp to top clamp) if you don’t the grease will fill the inner tube as well, the grease than takes the easiest route and will come out the bottom of the triple tree all over the tyre and the top all of the top triple tree.

    That said, yes I think its a good thing and am planning to do my bike and my suspension linkage soon.

    I never had to fit brgs to that XR.

    #115577

    DAVE PURDOM
    Member

    ITS for my sons yz 250 2t

    #115606

    Greg
    Member

    Yeah it will be fine, if it was me doing it though I would pull the the thing apart and inspect the brgs first, drill and tap the hole fit the nipple thus being sure no metal contaimates the lower brg during the process, then pack the brgs and reassamble, using the nipple every time I washed the bike. By the way it takes alot of grease to fill the headset area first time, but everytime after requires only a small amount

    TB

    #115607

    DAVE PURDOM
    Member

    Thanks trailboss yep i was worried about any drill swarf and fileings from tapping the hole
    yeah i may pull it down so i can see whats happening

    #115609

    Mick D
    Member

    Oh yeah,I bet this thread gets a ton of hits with the title it has…LOL

    #115610

    DAVE PURDOM
    Member

    micknmeld wrote:

    Quote:
    Oh yeah,I bet this thread gets a ton of hits with the title it has…LOL

    HMMMMM now i wonder who the first randy bugger was to have a look…. why it was you (micknmeld}..lol:laugh: Oh yeah probably should have been grease nipples ooooppps

    #115615

    Mick D
    Member

    Randy bugger?? I looked at it as a moderator to ensure it was in keeping with the strict posting rules we have here at OBT.LOL

    #115617

    DAVE PURDOM
    Member

    Nahhh if i really wanted to catch your attention i would have put something really good ….like aaahhhh..mmmmm …ALL BLACKS WIN WORLD CUP:laugh:

    #115620

    Greg
    Member

    laserracer wrote:

    Quote:
    Nahhh if i really wanted to catch your attention i would have put something really good ….like aaahhhh..mmmmm …ALL BLACKS WIN WORLD CUP:laugh:

    Or Referee wins world cup for all Blacks

    #115621

    DAVE PURDOM
    Member

    yeah sneeky huh .. hes on our side.. you guys will just have to get your own biased ref:P :)

    #115578

    Ray Fuller
    Member

    Trailboss wrote:

    Quote:
    Yeah my 1st XR600 was done, only thing is if the bike is a trail bike and has a steering lock fitted you need the fill the slot in the inner tube (triple tree tube, bottom clamp to top clamp) if you don’t the grease will fill the inner tube as well, the grease than takes the easiest route and will come out the bottom of the triple tree all over the tyre and the top all of the top triple tree.

    That said, yes I think its a good thing and am planning to do my bike and my suspension linkage soon.

    I never had to fit brgs to that XR.

    Do XR;s have suspension the one’s I’ve riden and owned had something but not suspension:woohoo:

    KTM01

    #115623

    Greg
    Member

    KTM01 wrote:

    Quote:
    Trailboss wrote:

    Quote:
    Yeah my 1st XR600 was done, only thing is if the bike is a trail bike and has a steering lock fitted you need the fill the slot in the inner tube (triple tree tube, bottom clamp to top clamp) if you don’t the grease will fill the inner tube as well, the grease than takes the easiest route and will come out the bottom of the triple tree all over the tyre and the top all of the top triple tree.

    That said, yes I think its a good thing and am planning to do my bike and my suspension linkage soon.

    I never had to fit brgs to that XR.

    Do XR;s have suspension the one’s I’ve riden and owned had something but not suspension:woohoo:

    KTM01

    :angry: When I come up there in Feb and bring my bike and kick you and your Orange shitboxes arse I will have a public apology for all that you have said about the bike that made trail riding what it is today in this country

    So there ! lol 👿 👿

    #115624

    Greg
    Member

    :P I am going to get my Honda lawn mower now and mow my lawn, see ya do that with ya ktm brand, maybe when they get there bikes sorted they can try making something else but let them get one thing sorted first Ray :laugh:

Viewing 15 posts - 1 through 15 (of 24 total)

You must be logged in to reply to this topic.