Seat cover which staple gun?

Home Forums General Bike Talk Seat cover which staple gun?

This topic contains 12 replies, has 0 voices, and was last updated by  Dean 12 years, 2 months ago.

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • #100442

    Hey guys, I want to replace the seat foam on my bike and need to re staple. Can someone tell me whether I need a Pneumatic staple gun or will a heavy duty spring loaded gun get through the plastic? Thanks Steve

    #208221

    Mick D
    Member

    Sorry DRool, as you were editing this post I deleted the other. You will have to post it again, sorry mate.
    Micknmeld

    #208222

    Thanks Micknmeld, you are to on the ball :)

    #208229

    Chris
    Member

    Steve I have tried with cordless stapler, power stapler and didn’t really have much luck, I ended up getting Suttos to do it for me, they use an air stapler, the problem with the electric one was I couldn’t get the staple to penetrate far enough you could use it and then bang them all the way in with a hammer…

    Cheers
    Chris.

    #208223

    Found it was cheaper to get the Upholsterer to staple the seat cover back on – cost $35 where the stapler was going to cost upwards of $50 to $100 for a reasonable one.

    #208224

    Stuart
    Member

    I’ve done a seat recover with a mechanical stapler & 5mm staples bought from Bunnings.

    Had no problem getting them in, just hold the stapler hard against the seat base so it isn,t forced away when stapling

    #208225

    Hmmm, probably would be cheaper to get the local upholsterer to do it but I like to have a crack at things myself and could use a stapler for other things I need to do around the house.
    I might try a mechanical stapler from the hardware tomorrow on the seat before I pull the old cover off.
    Thanks for the replies.

    #208235

    Bruce Curtis
    Member

    We are serial seat tearers here, so between Mrs Cee and i we have become fairly adept at this task, some gripper material from the upholsters a heat gun and a good pneumatic upholsters staple gun and you can do yer own for years to come.
    Gunna do the IT next week for Josh, the square eadged seat will be a bit of a challenge but nothing impossible, have tried quite few good mechanical and electric staplers… my advice is go air

    #208236

    Mick Pilgrim
    Member

    I bought a Project Air stapler from Bunnings for about $57 (as I had a few other jobs that were hard work with the hand stapler) and it worked great when I replaced the foam and cover on my 690.

    Was going to get a local upholsterer to do it but they were too busy, wanted to charge a ridiculous price or weren’t there when arranged to get it done. :(

    I got a few rows of stainless staples, Bunnings stapler and all is good. B)

    Mick

    #208226

    Well $57 isn’t much for a pneumatic one that works so I might check them out. Cheers

    #208227

    sounds like it worked at the end with the seats you wanted to replace .

    #208228

    I brought this little beast from a local tool store for a tad under $50 to do to seat on my husky.

    F76D8AC8-7C9B-4703-B830-FE164FCF8920-2808-0000081AE043A948.jpg

    It’s so strong I had to turn the reg on my compressor down as it would shoot staples straight through the seat pan. Bonus the misses brought some new ikea bedroom furniture for the girl recently. This made putting on draw bottoms and cupboard backs easy work.

    PS. Any exuse will do to buy a new tool.

    #235961

    Dean
    Member

    yep go the air stapler evey day avoid the Ozito ones they are crap.

    Hey Scotty dont you get dressed up in Uniform and holster up that beast. :laugh:

    “well tell me Punk,was that 5 shots or 6” go ahead make my day :laugh:

    Ollie

Viewing 13 posts - 1 through 13 (of 13 total)

You must be logged in to reply to this topic.