doug

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 41 total)
  • Author
    Posts
  • in reply to: 38mm Mikuni jetting on XR600 #159890

    doug
    Member

    done all of that the tank filter was good and tap was ok also checked the cap and it is not blocked carby cleaned the lot so where do i go from here

    in reply to: 38mm Mikuni jetting on XR600 #159886

    doug
    Member

    i have no idea it looks ok to me

    in reply to: 38mm Mikuni jetting on XR600 #159884

    doug
    Member

    Does not look warn and moves up and down freely

    in reply to: 38mm Mikuni jetting on XR600 #159882

    doug
    Member

    cleaned tank out and the fule tap was all good, carby is as clean as it is gonna get and blown out..
    Thinking maybe needing a new needle and seat..

    in reply to: 38mm Mikuni jetting on XR600 #159879

    doug
    Member

    well white rocket this carby dose not have such a screw but it dose have a nut on the bowl witch you can take out so i did what you seed with that out and fuel came out then slowed to a drip every couple of seconds is that bad

    in reply to: 38mm Mikuni jetting on XR600 #159878

    doug
    Member

    been using caltex vortex98 dont know if that has ethanol think in mite. :unsure: I changed the fuel line the last time i put the crrby back on so dont think that is the problem

    in reply to: 38mm Mikuni jetting on XR600 #159875

    doug
    Member

    still the same :angry: so what do look for now :unsure:

    in reply to: 38mm Mikuni jetting on XR600 #159857

    doug
    Member

    did all that Ollie and still hard to blow thru i tried some compressed air thru the line went thru ok going to try it back on the bike now

    in reply to: Trailrider Mag Exclusive to OBT #159848

    doug
    Member

    thanks TB will check it out

    in reply to: Trailrider Mag Exclusive to OBT #159845

    doug
    Member

    sorry man i dont have a printer can I email the form to them

    in reply to: Trailrider Mag Exclusive to OBT #142799

    doug
    Member

    this offer still stand TB and what do i have to do to get signed up

    in reply to: 38mm Mikuni jetting on XR600 #159452

    doug
    Member

    well got some time today to get the carby off

    pulled it apart and tried what you guys said about the float pivot pin and i got it out it was tapered on one side ;)

    the needle and seet looked good not stuck :unsure:

    so i pulled the thing to pieces and i mean the hole thing and gave it a good look over and it looks ok to me not a caby specialist by any means

    tried blowing thru the fuel line but it was very hard i mean very hard but it did stop at 45 degrees so is it meant to be that hard :unsure:

    in reply to: 38mm Mikuni jetting on XR600 #159436

    doug
    Member

    thanks guys for for your help :)

    well have not taken it off the bike yet will do later then i will pull it apart and try to get the needle and seet out to see what i looks like

    in reply to: 38mm Mikuni jetting on XR600 #159378

    doug
    Member

    I think that the pin dose have a taper on it still was very hard did not wont to brake anything

    will try blowing air thru the fuel line aswell

    in reply to: 38mm Mikuni jetting on XR600 #159367

    doug
    Member

    fuel is flowing out the tap
    gave it a good blow out before i put it on

    could not get to needle and seet out the pin was to tight to get out was going to brake the support dont know how to get it out??????
    going to try again tomorrow

Viewing 15 posts - 16 through 30 (of 41 total)