Go To...

Robert Jillett

Forum Replies Created

Log In Register Lost Password
Viewing 15 posts - 16 through 30 (of 130 total)
1 2 3 … 9
  • Author
    Posts
  • September 3, 2013 at 10:29 pm in reply to: Nundle – An attempt to Mount Bollocks ride report #249269

    Robert Jillett
    Member

    Sorry about that this is my first go at setting it all up and getting it going and it was pretty late last night.

    Hope it works ok now

    September 3, 2013 at 9:06 pm in reply to: Nundle – An attempt to Mount Bollocks ride report #248903

    Robert Jillett
    Member

    http://www.youtube.com/watch?v=geX6z5c3-is

    Cheers
    Robert

    September 2, 2013 at 10:48 am in reply to: No rear brake??????? #249083

    Robert Jillett
    Member

    Nickj has got it Murph.

    Take the calliper off and get it as low as you can, place something about the size of your disc between the pads.
    Make sure the tube on the bleed screw is tired on tight so no air can get in, place some brake fluid in a bottle and place the other end of the tube in this. Open your bleed screw up to start pumping the new fluid will come through and get the air out.

    Make sure the open end of your bleed hose always stays under the fluid in your bottle it can’t suck any air back in then.

    Hope this heaps.

    If all else fails just ride it without the back brake it didn’t seem to slow you down at all Sat Afternoon :laugh: :laugh:

    September 2, 2013 at 9:22 am in reply to: Nundle – An attempt to Mount Bollocks ride report #248901

    Robert Jillett
    Member

    I know it has already been said heaps but it is really appreciated the massive afford the Tamworth crew went to hosting a awesome weekend. Buzz and Boony for leading us on some of the best singles in OZ. :woohoo: :woohoo: :woohoo:

    House and Damus for sucking the dust all day and also waiting while we picked ourselves back up and dusted off.

    A great big thanks to the boys at the ring of knowledge i have never learnt so much stuff in so little a time :laugh: :laugh:

    Thanks again!

    Robert

    August 28, 2013 at 9:14 am in reply to: Happy B-Day Rob400 #248799

    Robert Jillett
    Member

    Thanks heaps for the birthday wishes. I have had a great day and got a heap of awesome gopro accessories :cheer: :cheer:

    Cant wait for the weekend to catch up with everyone and have a few beers i have got the old bulls stubby holder packed and it is ready for heaps of use.

    Cheers

    Robert

    August 9, 2013 at 5:48 am in reply to: Expressions of Interest for Knee Braces #246856

    Robert Jillett
    Member

    Sorry for the delay in getting back to you work and home life have been really busy.

    Bloody son blow up the gearbox in his car so my hidden funds have taken a substantial hit.

    At this stage i am only a maybe and will contact Sutto’s first thing Monday if i can get it to come together.

    I really appreciate the big effort that has gone into getting the lower price.

    Cheers

    Robert

    July 29, 2013 at 4:38 am in reply to: Expressions of Interest for Knee Braces #246844

    Robert Jillett
    Member

    Hi TB,

    Sorry to mess you around can i please change the size from XL to L

    After trying Nickj’s XL ( thanks heaps Nick) although when i measured my knee at 39.5mm when i fitted Nick’s on the XL’s were wound right in on the adjustors. I aslo had a thermo knee gaurd on at the same time.

    This might help some others that measure right on the limit of L to XL

    Thanks heaps

    Robert

    July 26, 2013 at 8:14 am in reply to: Expressions of Interest for Knee Braces #246840

    Robert Jillett
    Member

    Hi TB

    Ultra cells XL for me please if i am not to late.

    Cheers

    Robert

    July 25, 2013 at 11:29 am in reply to: Damaged Bolt Removal #246955

    Robert Jillett
    Member

    Best tip I can give here is if the bolt has broke because it is locked in the threads the chance of getting it out with an easy out is very low.
    Take you time and drill out the bolt even if you only keep going up one drill size at a time it is still a whole lot easier then trying to get a broken easyout out.
    Through the easy outs out of your toolbox all together

    July 25, 2013 at 11:18 am in reply to: Helicoil vs Time sert #246943

    Robert Jillett
    Member

    I have used the helicoil branded ones for a long time in my workshop and have found them easy to fit and extra strong.
    Have used them heaps in alloy chainsaw engines. The only negative I found was sometimes when you are removing a bolt were a coil has been used the coil can wind out as well.
    There are a lot of different ones on the market I also find that the size you have to drill out to fit the coil with helicoils is only minimal.

    Just my opinion
    Robert

    July 25, 2013 at 10:58 am in reply to: 2014 Beta 2 strokes #246999

    Robert Jillett
    Member

    350 looks good might be on my wish list

    July 25, 2013 at 10:56 am in reply to: Expressions of Interest for Knee Braces #246832

    Robert Jillett
    Member

    Hi
    I am interested will get back to you .soon with size and type
    Going back to physio in the morning for my knee
    I to am a case of the horse has already bolted
    Cheers
    Robert

    July 18, 2013 at 9:38 am in reply to: New to me Crf 450x 06 #246362

    Robert Jillett
    Member

    Nice one mate

    hang on tight

    July 10, 2013 at 6:01 am in reply to: Nundle – An attempt to Mount Bollocks 30/31stAugust-1stSeptember 2013 #239272

    Robert Jillett
    Member

    Hi Snowy,

    If there is room for one more at this ride can you please put me down.

    I have got the accom sorted if there is a spot.

    Cheers

    Robert

    June 10, 2013 at 9:56 am in reply to: Spuds Art Show Entry #243300

    Robert Jillett
    Member

    Great work Spud bloody awesome stuff :cheer: :cheer:

    Even better pics Nickj !!!!!! Did you copy the pic from the new hobbit movie :laugh: :laugh: :laugh:

    Robert

  • Author
    Posts
Log In Register Lost Password
Viewing 15 posts - 16 through 30 (of 130 total)
1 2 3 … 9